Petite
Purse Box
For this project, you will need the following Stampin’
Up! supplies:
1 sheet of 12”x12” Designer
Series Paper or 2 sheets of 8.5” x 11” cardstock. We will
actually only use a small portion of the second sheet of cardstock, so if you don’t
have two full sheets, that is okay.
Sticky Strip (#104294), Paper Snips (#103579), Bone Folder (#102300), Stampin’ Trimmer (#126889), Petite Purse Bigz L Die (#125606), Big Shot with the included Standard Cutting Pads (#113439).
Optional supplies: stamps, ink, ribbon or other embellishments to decorate the box with.
Sticky Strip (#104294), Paper Snips (#103579), Bone Folder (#102300), Stampin’ Trimmer (#126889), Petite Purse Bigz L Die (#125606), Big Shot with the included Standard Cutting Pads (#113439).
Optional supplies: stamps, ink, ribbon or other embellishments to decorate the box with.
Now that you’ve gathered your supplies, let’s get
started!
Step 1:
Using your trimmer, cut four pieces of paper into 4.25” x 5.5” rectangles (if
you are using an 8.5”x11” sheet of paper, that is cutting it in half once lengthwise
and then cutting those two pieces in half widthwise, essentially quartering the
paper). Also cut two squares of paper
measuring 2.75”x2.75” each. Set the
squares aside and gather all four rectangles.
Step 2: Using
your Big Shot, the Standard Cutting Pads, and the Petite Purse Die, cut 4 purse
shapes out. (TIP: cut one layer at a
time. If you cut more than one, there is
a good chance the lines that are intended to be scored will actually be cut.) You
will notice that we have trimmed the paper small enough that it doesn’t fit
over the whole die. That is okay. We are only going to use portions of the
purse shape, so align it so that it cuts out the parts we need according to the
photo below. The image below shows you what the purse die looks like when you
cut it from a bigger sheet of paper, so that I could show you the parts we will
cut off.
Step 3: Once you cut the die, it will look
roughly like the photo below. Using your
paper snips, trim off the nub at the top, the small side flap on the right and
the remainder of the large flap at the bottom. Do this on all four purse pieces.
TIP: When
trimming rounded shapes, like the nub at the top, hold your scissors in place
and rotate the shape as you slowly close the scissors. You’ll get a much smoother edge this way.
NOTE: I drew
the black lines on here to give you a reference point – you do not need to do
this step yourself.
Step 4: You will now be left the shape
below. Because this purse is intended to
be trapezoidal, when we try to create a box with it, parts of the flaps are
going to be too long, and will stick out if we don’t trim them. In the photo below, you will see that I have
drawn some black lines at angles. We are
going to trim the flaps along these black lines. This is not an exact science, so don’t sweat
it, just eyeball it. You don’t have to
draw the lines, unless that makes you feel more comfortable. Do this on all four pieces.
Step 5: Now is your chance to decorate the paper if you are going
to. The sky is the limit, so have fun
with this step! Some ideas include dry
embossing with our Textured Impressions Embossing Folders, heat embossing with
any color of embossing powder (or for a fun seasonal treat, check out our
holiday-scented embossing powder), regular ink and stamps, etc. If you want the
inside to be as pretty as the outside, decorate both sides or use our Designer
Series Paper which is two-sided. Now is
also the time to decorate the bottom piece, if you wish. Grab one of the squares we cut in Step 1 and
decorate one side of it. This will be
the outside of your bottom. If you want
the inside bottom decorated, then stamp one side of each square.
TIP: If you only want the outside decorated, make sure you decorate the same side of each piece. To do this, lay out all of four pieces so that they are oriented the same way (i.e. all side flaps on left, or all side flaps on right), and then decorate the same side, or run it through the embossing machine the same way). Keep in mind the bottom flap and the side flap will not be visible when we are done, so they don’t have to be fully decorated. In my case, I chose snowflakes and I wanted the snowflakes to go off the edges, so I ended up stamping on those flaps anyway, but it’s not necessary.
TIP: If you only want the outside decorated, make sure you decorate the same side of each piece. To do this, lay out all of four pieces so that they are oriented the same way (i.e. all side flaps on left, or all side flaps on right), and then decorate the same side, or run it through the embossing machine the same way). Keep in mind the bottom flap and the side flap will not be visible when we are done, so they don’t have to be fully decorated. In my case, I chose snowflakes and I wanted the snowflakes to go off the edges, so I ended up stamping on those flaps anyway, but it’s not necessary.
Step 6: Using your bone folder, fold each
flap on the score lines (see black lines in photo above in Step 4 for
reference). You will want to make sure
you have the side you intend to be the inside of the box facing towards you and
then fold the flaps towards you.
Step 7: Now the fun of assembling
begins! Get out the Sticky Strip and
your Paper Snips. Put the Sticky Strip
on all pieces as shown below. Don’t peel
off the backing just yet. TIP: The top
of your box is going to be the end the rounded flap is on. So if your Sticky Strip doesn’t run the full
height of the flaps, at least make sure it runs right up to the top. Be generous with your Sticky Strip as it
makes for a sturdier box.
Step 8: Grab one of your square bottoms. This one will be seen from the inside, so if
you want the inside decorated, make sure you have the pretty side up. You are going to adhere the bottom flap of
each of the four purses to each of the four sides of the square. Start with one piece of the purse and peel
all the backing off the sticky strip on the bottom flap (leave backing on the
side flap for now). Line up the edge of
the square with the crease between the bottom flap and what will be the side of
the box. Adhere it with the flap ending
up on the outside (bottom) and square ending up on the top (what will be inside
of box). I like to use my bone folder to
rub it over the layers and secure the adhesive.
Repeat on all four sides. If you
want the outside bottom decorated, add your second square to the outside with
the pretty side facing down.
Step 9: Now we are going to
work on the sides. Flip your project
over so that the inside of your box is facing up. Now peel the backing off the Sticky Strip on
one flap (only do one flap at a time to avoid sticking things together
unintentionally). Adhere the flap to the
inside of the side next to it. Line it
up so that the edges are even. Repeat on
all four sides. You may find your bone
folder will help you get into the tight spaces to rub down the adhesive. Here’s what it will look like after the first
two sides are stuck together:
Step 10: You have now created your box. You can play with different ways to close it,
and different ways to decorate the top.
For this tutorial, I simply laid down the four sides and tied it shut
with ribbon. In another example (click here), I laid down two of the flaps opposite each other and then
pulled the other two flaps together to create a tent. Again, this is an opportunity for creativity
so have fun with this! If you would like this tutorial in a word document or need help ordering these supplies, or have questions, please feel free to contact me.
